The Enerzeppelin

10 September 2008 at 22:50 | Posted in Energy Farm, Green Energy, Green Initiatives, Inventions, Renewable Energy, Wind Energy, Wind Power | Leave a comment
Tags: , , , , , , , , ,

[Category: Inventions. If you are new to my blog please read the “About itimes3” page first]

Wind tends to happen more higher up in the sky. You can build a windmill on a tall pole to capture the wind and generate electricity, but that means that you have a fixed location that needs extensive preparation, and the windmill is not going away for many years, so a lot of planning is required.

But what if we could launch a windmill that would capture the winds at the same height as commercial windmills, but could be packed up in an hour or less, and be redeployed elsewhere?

Enter the “Enerzeppelin”. The Enerzeppelin could be manufactured in different sizes, and in different configurations, depending on requirements and what investment people would want to make.

The basic concept is that of a zeppelin-shaped gas balloon, with, depending on windtunnel and practical research results, either a tunnel lenghtwise through its center which would be fitted with one or more power-generating windmills, or several windmills deployed on a frame underneath or around the zeppelin, or both. The total number and wind-generating surface area of windmills deployable would depend on calculations and testing, and could vary depending on local conditions.

In addition to the windmills, the upper surface of the zeppelin would be fitted with solar cells, to capture the rays of the sun. These cells would either need to be of flexible construction, or have sufficient space between them to allow for the zeppelin to be folded away for storage without breaking them. In some circumstances, such as where the Enerzeppelin will be redeployed and moved frequently, it may be more economical in terms of price/performance to mainly focus on the windmills, and not fit the solar cells.

The overall concept would be as follows: the Enerzeppelin is deployed from either a building, a truck, a van, the bed of a pickup-truck, a trailer, or a (wheeled) crate, depending on its size. Where useful, the vehicles should be custom-adapted for the Enerzeppelin, to enable practical and quick launching and recovery. The larger versions of the Enerzeppelin would need to be anchored to a fixed object such as a building, whereas smaller versions, depending on wind conditions, could be anchored to a vehicle. In some locations, where this is easily possible, the vehicle could be fitted with inflatable ballast tanks, which could be filled with water pumped from streams or lakes with a handheld electrical pump, to provide extra anchoring security.

For city use, a new anchoring system could be developed whereby a sewage drain is used for anchoring, by means of an expandable metal anchor being lowered into it, and expanded at the bottom (opening umbrella idea), which would lock it into place. Similarly, anchors could be developed to wrap around the base of light poles.

Due to the cost of the gas to fill it with (hot-air versions, heated by solar power perhaps, could also be researched), there will be a minimum deployment period for the Enerzeppelin, below which it is uneconomical to use it, unless it were not deflated but simply towed, or parked atop a vehicle, for transport to its next deployment location.

The gas to fill the Enerzeppelin with could either be hydrogen (which is cheaper, but flammable) or helium, which is more costly.

The Enerzeppelin could be deployed permanently on some sites, although this would typically be remote sites such as farms, or remote industrial areas which are not subject to intervention from neighbours. Oil rigs out at sea could be equipped with them, and they could be used to power remote outposts of any kind. They could be deployed from ships or barges at anchor, and smaller versions, particularly if they were lifted using hot air, could be deployed to power small villages or individual homes or businesses in third world countries, or generally in remote locations anywhere on the planet.

The vehicle the Enerzeppelin is deployed from would be equipped with batteries to store the power generated, and/or a system to feed the power into the grid or into direct usage. More advanced versions could use the power to generate oxygen and hydrogen from water, which could be used for energy generation using fuel cells, or the hydrogen could be used to keep the Enerzeppelin afloat. The latter would be very useful in third-world countries, as gas would be difficult to source commercially there, provided there is river water or similar to use.

Enerzeppelins could be used to power events at remote locations, such as pop concerts, and they would also be useful in places where there is a sudden demand for power but no supply, such as disaster zones. Their easy portability in custom-designed vehicles or crates would make it easy for them to be dropped into disaster zones by helicopter. A small model should be able to power a set of freezers or fridges, as well as lights.

The wire with which the Enerzeppelin is tethered could be equipped with a number of Wiremills (see my separate post), to generate additional energy, provided the weight of the Wiremills is not too great.

The concept of the Enerzeppelin is valuable because it will be readily deployable in any location globally where there is sufficient wind to generate electricity (the wind does not have to be strong, as the Enerzeppelin is attached to batteries, which will fill up over time regardless of wind speed).

In areas where there is permanent wind, instead of a zeppelin-type balloon, a kite or glider could be used, which would do away with the requirement for the gas to keep it aloft. This would operate under the same principle.

If you like this idea and you work in a type of industry where this is relevant, I would be happy to discuss in more detail, answer questions or assist in other ways. For details and contact information please see the “About itimes3” page.

George Spark

Disclaimer: Any trademarks mentioned herein are the property of their respective owners.
All usage of this site is entirely at users risk.

The Wiremill

10 September 2008 at 22:44 | Posted in Energy Farm, Green Energy, Green Initiatives, Inventions, Renewable Energy, Wind Energy, Wind Power | Leave a comment
Tags: , , , , , , , , , ,

[Category: Inventions. If you are new to my blog please read the “About itimes3” page first]

The Wiremill is a small to medium-sized power-generating windmill that could be deployed on wires or poles.

Rather than having a set of blades spinning, the whole device (casing) spins around a fixed centre, which houses a dynamo-type power generation device. The principle is similar to wind-driven ventilators that are fitted to roofs or sometimes vans or buses.

Wiremills could be made in different shapes or sizes, and could be coloured to blend in with the surroundings. They could be fitted for permanent use, or models could be developed that could “clip on” to poles, wires or cables. Multiple Wiremills could be used above each other.

A special model could be developed to fit the top of flagpoles or masts, for permanent use.

Wiremills could be deployed on masts that hold up equipment on top of buildings, on flagpoles, on bridges equipped with cables or wires, or “forests” of masts with wiremills could be specifically “planted” atop buildings or on open terrain in the city and elsewhere.

The main purpose of the wiremill is to generate some extra power, simply because there is an unused wire or pole nearby so why not use it. In large numbers, the wiremills could contribute significantly to power generation.

The idea is that the wiremill is to be made from cheap materials, including recycled metals, and be designed so that it can be quickly deployed to wires, cables and poles of different sizes.

Power cables should be attached by means of a plug system (like one plugs a headphone into a music player) so that wiring can be done quickly.

The product range should include different “base stations” where power is collected in batteries and/or standardized for supply to the grid.

If you like this idea and you work in a type of industry where this is relevant, I would be happy to discuss in more detail, answer questions or assist in other ways. For details and contact information please see the “About itimes3” page.

George Spark

Disclaimer: Any trademarks mentioned herein are the property of their respective owners.
All usage of this site is entirely at users risk.

Cell Phone Dating Using Bluetooth

26 August 2008 at 17:32 | Posted in Bluetooth, Cell Phone, Cell Phone Dating, Cell Phone Security, Electronic Identification, Inventions, Mobile Phone, Mobile Phone Dating, Mobile Phone Security, Security Access Systems, Social Networking | Leave a comment
Tags: , , , , ,

[Category: Inventions. If you are new to my blog please read the “About itimes3” page first]

Observation one: Have you ever had your cell phone’s Bluetooth on when entering a bus or a train, and looked at the Bluetooth devices list? Every time I do this, a whole list of devices pops up on my screen: many people have Bluetooth, and they keep it on at all times.

Observation two: Dating and generally meeting people can be a difficult game. In many cultures, particularly the Western ones (as opposed to Latin and some other cultures), people can easily be lonely because they cannot seem to find the right way to approach others and fear of rejection is culturally more emphasized. In addition, many old people are lonely because they may lose their partner and then do not know how to find new friends. Other examples can easily be added.

Observation three: Almost everyone has a cell phone these days, and almost all cell phones have Bluetooth.

So: what if someone wrote an application that would compare a set of “flags” (software switches that can be set to either “yes” or “no”) in a cell phone with a set of flags in another cell phone.

If a pre-set number of flags match, the owners of both sets (or only one, depending on setup of the system by each user) would be notified.

It would work like this: When I set up the system, a large number of questions is asked and answered (for easier use, the questions could perhaps be answered online or at least on a computer, with the answers transferred to the cell phone, to avoid having to type it all on the small keypad of the phone). The questions could include (first) name, sex, age, area where living, many questions on a wide range of interests (based on drop-down menus, to ensure exact keyword matching), type of relationship wanted (friendship, one-night-stand, serious relationship, or even business relationship, etc.), plus various user-determinable settings.

The system would allow for active or passive “trawling” (for example, I could set my phone to only “listen” on Bluetooth and alert only me to a nearby “match” with my flags, or I could set the phone to also “broadcast” so the other user would also be alerted to a match happening).

Additionally, users could be flagged as “registered” (e.g. identity verified) by for example the cell phone company, which would add a layer of security for a matching user.

This system could be used as an additional layer of convenience for dating in nightclubs and bars, but also in the bus or the supermarket, for example.

Additionally, people could find potential friends with the same interest. This would also be beneficial for older people, who often are alone.

Finally, an adaptation of a system like this could be used for identification and security purposes, with a “locked” set of flags in the phone, in combination with a picture and perhaps other identifying and/or security data,¬†allowing the phone to be used as an access tool (to confirm someone’s eligibility to enter or be somewhere, for example).

NOTE (added 28 August): I just found out that apparently there are already services like this in existence. Don’t have time to check it out right now but you might be able to google for details… As I mention in the “About itimes3” page, I don’t usually check for details and at times an invention or idea I publish may already exist, which is apparently the case with this one.

If you like this idea and you work in a type of industry where this is relevant, I would be happy to discuss in more detail, answer questions or assist in other ways. For details and contact information please see the “About itimes3” page.

George Spark

Disclaimer: Any trademarks mentioned herein are the property of their respective owners.
All usage of this site is entirely at users risk.

Blog at WordPress.com.
Entries and comments feeds.